Frigidaire Gallery Oven Not Heating — Common Causes
When a Frigidaire Gallery oven stops heating — whether it is a range, wall oven, or double oven — the problem is almost always one of a short list of components. As an authorized Electrolux/Frigidaire servicer, we see these failures regularly. Here is what to check and what each problem means.
Bake Element (Electric Ovens)
The bake element is the heating coil at the bottom of the oven cavity. When it fails, the oven will not heat in bake mode. You may still have broil (the top element) working normally.
What to look for: Visible damage — blistering, holes, cracks, or a break in the element. Turn the oven to Bake and look at the bottom element. It should glow red evenly across its entire length. Dark spots or no glow at all mean the element has burned out.
What it usually means: Element replacement. This is one of the most common and straightforward oven repairs.
Igniter (Gas Ovens)
On gas Frigidaire ovens, the igniter is the most common failure point. The igniter heats up to open the gas valve — if it cannot get hot enough, the valve stays closed and no gas flows to the burner.
What to look for: Turn the oven to Bake and watch the igniter (visible at the back of the oven floor near the gas burner). It should glow bright orange within 60 seconds and the burner should light. If the igniter glows weakly (dim orange) for several minutes without the burner lighting, it is too weak to open the gas valve.
What it usually means: Igniter replacement. A weak igniter draws enough current to glow but not enough to open the safety valve. This is the number one cause of gas ovens not heating.
Temperature Sensor (RTD)
The oven temperature sensor is a probe mounted inside the oven cavity, usually near the top back wall. It measures oven temperature and sends the reading to the control board. If the sensor fails or reads incorrectly, the oven may not heat at all, overheat, or cycle erratically.
What to check: The sensor should read approximately 1,080 ohms at room temperature when tested with a multimeter. If it reads open (infinite resistance) or significantly off from 1,080 ohms, it has failed.
What it usually means: Sensor replacement. The sensor itself is inexpensive. Occasionally, the issue is the wiring harness between the sensor and the board rather than the sensor itself.
Control Board
The electronic control board manages oven temperature, timing, self-clean cycles, and error code display. When the board fails, the oven may not respond to temperature settings, may display error codes, or may not heat at all.
Signs of board failure: Oven does not respond when you set a temperature. Error codes appear with no obvious cause. The oven turns on and off randomly. Multiple functions stop working at once.
What it usually means: The control board needs repair or replacement. On Frigidaire/Electrolux ovens, control boards can often be repaired at the component level — relays, capacitors, and other individual parts can be replaced without buying an entire new board.
Broil Element
The broil element is at the top of the oven cavity. While it primarily handles broiling, some Frigidaire models also use the broil element during preheat or in convection mode. If the broil element fails, you may notice uneven heating or the oven taking much longer to reach temperature.
What to look for: Same visual inspection as the bake element — look for breaks, blistering, or dark spots. Turn on Broil mode and check that the top element glows evenly.
Safety Valve (Gas Ovens)
The safety valve controls gas flow to the oven burner. It only opens when the igniter draws enough current. If the safety valve fails internally, gas will not flow even with a good igniter.
Important: A failed safety valve is less common than a weak igniter. Always test the igniter first — replacing the safety valve when the real problem is a weak igniter is a common misdiagnosis.
Thermal Fuse
The thermal fuse is a safety device that cuts power to the oven if it overheats. Once a thermal fuse blows, the oven will not heat until the fuse is replaced. Thermal fuses do not reset — they are one-time-use components.
What triggers it: A self-clean cycle that overheated, a failed temperature sensor that allowed the oven to overshoot, or a wiring issue.
Important: If the thermal fuse blew, find out why before just replacing it. Something caused the oven to overheat, and that root cause needs to be addressed.
Self-Clean Door Latch
On Frigidaire ovens with a self-clean cycle, the door latch must fully engage before the oven will enter self-clean mode. If the latch assembly fails, the oven may lock you out (F5 E1 error) or refuse to start the self-clean cycle. On some models, a latch failure can also affect normal oven operation.
When to Call
If you smell gas and the oven is not lighting, turn off the gas supply and call immediately. If the oven has no heat and a power cycle does not help, a component has failed and needs diagnosis. We service all Frigidaire and Electrolux ovens in Lubbock.
Schedule an oven repair or request a repair online.
Frequently Asked Questions
Q: Why is my Frigidaire oven not heating up?
A: The most common causes are a burned-out bake element (electric) or a weak igniter (gas). Visually inspect the element for damage, or watch the igniter — if it glows dimly for minutes without lighting the burner, it is too weak.
Q: Is Lubbock Appliance Repair authorized for Electrolux and Frigidaire?
A: Yes. We are an authorized Electrolux/Frigidaire servicer for warranty and out-of-warranty repairs.
Q: Can oven control boards be repaired instead of replaced?
A: Yes. We offer component-level board repair. Individual relays, capacitors, and other parts can often be replaced rather than buying an entire new board.
Q: How much does a Frigidaire oven igniter replacement cost?
A: Igniter replacement is one of the more affordable oven repairs. Contact us for a specific estimate based on your model.
Oven not heating? Request a repair or call (806) 730-6300.
